New products

LeafCoat 100% Organic Plant Strengthener Against Fungi and Plagues. LeafCoat is a Ready To Use product that was developed to restrain evaporation. It is made of natural latex. LeafCoat strengthens plants and provides them with a powerful expelling effect on harmful insects. It also prevents against harmful leaf fungi.

Leaf Coat is a ready made product with a dual function:

as a plant enhancer,
as protection against unwanted insects and fungi.
Leaf Coat is made of a natural latex which to be nebulized after creates a protective layer on the leaves. This layer remains approximately 1 to 2 weeks present. The protective layer closes the blade not finished so that light, air and water are allowed to pass.

Bio Optimal anti-elongation works yield-increasing. Endocrine systems of the plant becomes fully disturbed by the unnatural transition from 18 to 12 hours and the plant goes into a state of emergency growth. The crop then puts all her energy into it as long as possible. This is at the expense of the ideal structure.

Through its hormone treatment with Bio Optimal Anti-cell elongation this disturbance is restored, with the result that the crop remains short and compact. The plant puts all its energy not in distress, but switch earlier to flower formation, with the result that the crop is ready to harvest earlier.

The development of root growth, and stem thickness stays normal.

A new German made quality digital thermostat for accurate control of your growing temperatures. Useful for Bio Green Soil Warming Cables or any other heating device that has a 13 amp mains plug. This thermostat removes any need for wiring expertise for the home gardener and will control any device up to 3 Kw. This new unit also has a cool setting to turn on a fan as temperatures rise in the summer. Easy to operate, you set the required temperature using push buttons, with temperatures clearly shown on the large digital display.

• Temperature range 0-40 C (32-104 F).
• Temperature is measured by an encapsulated thermistor / sensor on the end of a 1 metre cable.
• Maximum operating load is 3000w

Build your own propagator with these Bio Green soil warming cables or use as under soil heating in your greenhouse. Soil warming cables are mains operated, fully insulated, safe and easy to use (full instructions supplied). Soil Warming Cables are recommended for areas of 0.5 sq.m.(25W), 1.0 sq.m.(50W), 1.2 sq.m.(75W), 1.5 sq.m(100W)., and 4.0 sq.m.(320W), respectively. We recommend that you use the Bio Green Digital thermostat TR-E (JH1727) with these Soil Warming Cables for accurate temperature control and ease of connection. (Please note that the moulded plug on the heating cable must NOT be removed if attempting to wire these heating cables to any other thermostat)

A soil warming cable is the ideal way to propagate seeds and cuttings on a greenhouse bench. A simple frame can be constructed from wood to form the propagating area required, which is them lined with polythene. The cable is laid onto a 5cm of horticultural sharp sand and covered with a further 5cm of sand. Alternatively the cable can be laid out on to an insulating material like polystyrene sheet and covered over with tin foil then a layer of polythene and then some felt matting to hold moisture under the seedtrays.

The cable is normally laid in runs 8 cm to 10 cm apart. This layout will allow you to raise the soil temperature by 11-13 C, above the greenhouse ambient. Higher temperatures can be achieved by laying the cable runs as close together as 5cm. In this case a thermostat should be used to precisely control the soil temperature to avoid over heating.

Build your own propagator with these Bio Green soil warming cables or use as under soil heating in your greenhouse. Soil warming cables are mains operated, fully insulated, safe and easy to use (full instructions supplied). Soil Warming Cables are recommended for areas of 0.5 sq.m.(25W), 1.0 sq.m.(50W), 1.2 sq.m.(75W), 1.5 sq.m(100W)., and 4.0 sq.m.(320W), respectively. We recommend that you use the Bio Green Digital Thermostat TR-E (JH1727) with these Soil Warming Cables for accurate temperature control and ease of connection. (Please note that the moulded plug on the heating cable must NOT be removed if attempting to wire these heating cables to any other thermostat)

A soil warming cable is the ideal way to propagate seeds and cuttings on a greenhouse bench. A simple frame can be constructed from wood to form the propagating area required, which is them lined with polythene. The cable is laid onto a 5cm of horticultural sharp sand and covered with a further 5cm of sand. Alternatively the cable can be laid out on to an insulating material like polystyrene sheet and covered over with tin foil then a layer of polythene and then some felt matting to hold moisture under the seedtrays.

The cable is normally laid in runs 8 cm to 10 cm apart. This layout will allow you to raise the soil temperature by 11-13 C, above the greenhouse ambient. Higher temperatures can be achieved by laying the cable runs as close together as 5cm. In this case a thermostat should be used to precisely control the soil temperature to avoid over heating.

Adjust net above your plants in the growing fase and your plants will grow through the net during Blooming
 

• Digital readout

• 2 windows (Temperature / Humidity)

• Memory for minimum and maximum temperature / humidity

• With batteries

• External Sensor